Board logo

標題: [教學] TOYOTA MR2 Valve Clearance Adjustment [打印本頁]

作者: carwing    時間: 2011-1-31 01:11 PM     標題: TOYOTA MR2 Valve Clearance Adjustment

Here are some notes pertaining to adjusting the valve clearance        on a 1991 Toyota MR2 Turbo.  
  Start off by removing the basics - the strut tower brace, and air tubes leading  to the throttle body.  Remove the throttle body pipe and bracket.  Loosen  the 4 bolts holding the throttle body to the intake, remove the air hose at  the base, cold start injector connector, and throttle position sensor connector.  There  is no need to remove the coolant lines leading to the throttle body.  The  body can be moved aside after the EGR valve is disconnected.  Remove the  spark plug wires, and PCV rubber hose going back to the intake pipe before  the turbo inlet.
  I found it necessary to just move the BOV pipe (ie the pipe from the high  pressure side of the turbo to the intercooler inlet) out of the way.
  The valve cover can now be removed using a Phillips screwdriver.Next up is to measure the valve clearance.  First the crankshaft must  be positioned correctly.  I found it easiest to remove the passenger side  rear tire, and one of the undercovers to get to the crankshaft bolt (19mm).  To  see the timing mark, the passenger side engine cover (up top) has to be removed  as well.  Then the crankshaft is turned clockwise until the timing mark  on the crankshaft pulley lines up with the 0 degree mark.  The valve lifters  on the #1 cylinder should be loose - and they should be tight on the #4 cylinder.  If  they are not, just run the crankshaft around 360 degrees.  At this point  the #1 and #2 intake valve clearance can be measured,  and the #1 and #3 exhaust valve clearance can be measured.  I  used a standard feeler gauge and recorded the value of the feeler that would  fit and the next higher thickness value that would not fit.  Here are  my notes:

      

Intake spec is              between .15 and .25mm.
        
#1 both between .178mm and .203mm.
  #2 left between .203mm and .228mm - right between .178mm and .203mm
  #3 both between .203mm and .229mm
  #4 left between .178mm and .203mm - right between .152mm and .178mm
  
  Exhaust spec is between .20mm and .30mm.
  
#1 left between .254mm and .279mm - right between .305mm and .330mm
  #2 both between .279mm and .305mm - left is slightly tighter.
  #3 both between .279mm and .305mm
  #4 both between .229mm and .279mm - right is slightly tighter.

      

Amazingly after 127,000 miles none of the          intake valve clearances were out of spec in the slightest!  In          this case, I decided to change out the #1, #2, and #3 exhaust valve          shims.
  The shims can be removed without using Toyota's SST (special service tool).  I  used an Allen wrench and a screwdriver.  It is a good idea to put tape  around the screwdriver tip so as to avoid scratches.  The Allen wrench  can be used to push the valve down - then the screw driver is placed between  the camshaft and the lip on the bucket to keep the valve spring compressed.  The  shim can then be removed using a magnet finger and where necessary pushing  it a little with another smaller screwdriver.
  Once the shims are removed, it is a good idea to label them (ie Exhaust  #1, left side).  A caliper can then be used to measure the thickness of  the removed shim.
  Once the thickness of the removed shim, and the valve clearance with the  old shim in place is determined, a value can be calculated for the new replacement  shim that will put the clearance back into Toyota's specification.
  For the intake, the formula is N = T + (A - 0.20mm)
  
For the exhaust, the formula is N = T + (A - 0.25mm)N = new shim thickness (mm)
  T = old shim thickness (mm)
  A = measured valve clearance (mm) with the old shim in place.
  For this I took the average of the value that would fit and the value that  would not fit.  For example, if I measured with the feeler gauge that  .279mm would fit, but .305mm would not, I would average those values to come  up with 0.292mm for the 'A' value in the equation.  For reference here  are the measured used shim thickness that I found for the #1, #2, and #3 exhaust  valve shims.

      

Exhaust #1 - Left            2.794mm   Right - 2.794mm
  Exhaust #2 - Left 2.8956mm  Right - 2.8702mm
  Exhaust #3 - Left 2.8194mm  Right - 2.8194mm

  
  
The calculation for the new exhaust #1 left shim would  be:
  2.794mm + (0.2665mm - 0.25mm) = 2.8105mm.
  Toyota supplies shims from 2.00mm to 3.30mm in increments of .05mm.  So  here we have a choice of 2.80mm or 2.85mm.  I choose 2.80mm.
  
  The calculation for the new exhaust #1 right shim would be:
  2.794mm + (0.3175mm - 0.25mm) = 2.8615mm.
Here I choose to use the 2.85mm replacement shim.

      

I choose to purchase a new valve cover gasket          along with the new shims from Toyota.
  The new shims can then be put in.  Again, using the Allen wrench and  a screwdriver to hold the bucket down, the new shims can be put in.
  Once the new shims are in place, the valve clearance should be re-checked.  In  my case, one of the shims was too tight and another was too loose, but by using  some of the old shims, I was able to get them very close to 0.25mm.  The  valve cover can then be installed - use some silicon sealant to seal around  the camshafts and distributor (6 places in all).
   The throttle body, spark plug wires, EGR valve, and various piping etc.  can now be re-installed.


作者: Aenergy    時間: 2011-2-1 09:27 AM

NY 唔多覺有“二號先生”喺街行...
應該劏得八八九九
作者: carwing    時間: 2011-2-1 09:53 AM

NY 唔多覺有“二號先生”喺街行...
應該劏得八八九九
Aenergy 發表於 2011-2-1 09:27 AM
一里通,萬里明
好多車啱用
作者: chin5003    時間: 2011-2-4 11:35 AM

thank q friend keep your job




歡迎光臨 公仔箱論壇 (http://5.39.217.76/) Powered by Discuz! 7.0.0